Deals
Home 9 Deals
Showing 421–445 of 445 results
DT16 | Deutsch Connector A 007-850
$101.29Add to cartM64X | Connector Harness Set 007-036
$531.07Add to cartM640 | Connector Set 007-035
$235.06Add to cartM840 | Connector Harness 016-168
$264.98Add to cartDSEM040 | M64X Development Kit
$2,448.48Add to cartDSEM640 | Programmable Controller (68 I/O)
$2,985.94Add to cartDSEM643 | Programmable Controller (34 I/O)
$1,642.29Add to cartDSE2133 | RTD/Thermocouple Input Expansion Module
$368.99Add to cartDSE9474 Battery Charger
$944.99Add to cartDSE9476 Battery Charger
$782.42Add to cartDSE8660 MKII | Auto Transfer Switch & Mains (Utility) Control Module
$1,798.93Add to cartDSE8680 Synchronising Generator Bus Tie Control Module
$1,615.99Add to cartBasler AVR AVC63-7 | Original
Read moreCaterpillar AVR VR6 | Original
Read moreOriginal | Mecc Alte AVR SR7/2-G | Electronic Voltage Regulator | 391600126
$406.00Add to cartOriginal | Mecc Alte AVR UVR6/1-F | Electronic Voltage Regulator | 391600117
$520.99Add to cartAVR AS440 | Original
Read moreAVR MX321 | Original
Read moreAVR MX341 | Original
Read moreLeroy Somer R230 | Original
Read moreLeroy Somer R250 | Original
Read moreLeroy Somer AVR R438 | Original
Read moreLeroy Somer AVR R448 | Original
Read moreLeroy Somer AVR R449 | Original
Read moreLeroy Somer AVR R450 | Original
Read more
Showing 421–445 of 445 results
DT16 | Deutsch Connector A 007-850
WEIGHT 0.1 kg/3.5 oz $101.29Add to cartM64X | Connector Harness Set 007-036
- Set of 3 coded AMP SEAL connectors pre-wired with 1.2 m (3ft 11") cable.
- Note: Suitable for development use only
- WEIGHT 1.4 kg/3 lb 1 oz
M640 | Connector Set 007-035
- Set of 3 coded AMP SEAL connectors complete with crimps/contacts.
- WEIGHT 0.4 kg/14 oz
M840 | Connector Harness 016-168
- Coded M840 connector pre-wired with 1 metre cable.
- Note: Suitable for development use only
- WEIGHT 0.5 kg - 1lb 2 oz
DSEM040 | M64X Development Kit
$2,448.48Add to cart- Development breakout PCB for application development.
- Multiple power configurations.
- Access to all inputs and outputs via sprung terminal blocks.
- Individual power and ground connection via 4mm connectors.
- Ethernet programming cable and USB data cable included.
- Suitable for M640 and M643 controllers.
DSEM640 | Programmable Controller (68 I/O)
- Controller specifically designed for mobile applications.
- Powerful 32 bit processor with 220 MHz clock speed.
- 32 configurable inputs with digital and analogue capability.
- 4 independent CAN interfaces, J1939, CAN open and RAW CAN.
- Ethernet interface for communications.
- Flexible user programming via CODESYS 3.5.
DSEM643 | Programmable Controller (34 I/O)
- Controller specifically designed for mobile applications.
- 4 MB application memory
- 16 configurable inputs with digital and analogue capability.
- 18 configurable outputs with digital, PWM and PWMi.
- Ethernet interface for communications.
- Flexible user programming via CODESYS 3.5.
- Ruggedised die cast aluminium housing for IP67 protection.
DSE2133 | RTD/Thermocouple Input Expansion Module
- Power on/link lost LED.
- 1.2km (0.75 Mile) working range.
- Connect maximum of 4 x DSE2133’s to a single host controller.
- Rotary ID switch to select address of DSE2133 to talk with host module when multiple DSE2133 modules are in use.
- Max of 32 RTD/thermocouple inputs.
- Compatible with J-type and K-type thermocouple, PT 100 and 3 wire RTD sensors.
PRODUCT VARIANTS 2133-01 – 2133 RTD/Thermocouple Input Expansion Module$368.99Add to cartDSE9474 Battery Charger
- 94.5% efficiency at high line full load.
- No external intervention for boost mode required.
- Works at high ambient temperatures.
- Fanless design.
- Plastic terminal cover available for safety.
- Lightweight design.
DSE9476 Battery Charger
PRODUCT VARIANTS 9476-01 – 24 V 20 A Intelligent Battery Charger- Intelligent two, three & four stage charging profiles.
- DSE Configuration Suite PC Software.
- External remote display option (DSE2541).
- DSENet® expansion.
- Battery charging temperature compensation.
- Automatic power de-rating at high ambient temperatures.
- Cell charge boost and equalizing.
$782.42Add to cartDSE8660 MKII | Auto Transfer Switch & Mains (Utility) Control Module
- Display sets on load on modules LCD display.
- Multiple mains (utility) capability (with additional module).
- Sequential set start.
- Configurable inputs/outputs (12/8).
- Data logging (USB Memory Stick).
- DSE Configuration Suite PC Software.
- Tier 4 CAN engine support.
DSE8680 Synchronising Generator Bus Tie Control Module
- Connects to two DSE MSC links (Bus 1 & Bus 2).
- Configurable inputs/outputs (11/8).
- Remote communications (RS232, RS485 x2, Ethernet).
- Data logging (USB Memory Stick).
- DSE Configuration Suite PC Software.
Basler AVR AVC63-7 | Original
- < ± 1.5% Regulation
- Soft Start Voltage Ramping – Sensing Voltage Loss Protection
- 120 or 240 VAC Sensing, Jumper Selectable Under Frequency Roll Off Protection
- With Under Frequency LED Indicator
Caterpillar AVR VR6 | Original
- Power: Shunt excited.
- Input: 180–280 VAC, 50/60 Hz, single-phase or three-phase.
- PMG Excitation: 63–105 VAC, 100/240 Hz, three-phase.
- Sensing Input: 180–240 VAC, 50/60 Hz, single-phase or three-phase.
- CT Input: 1 A or 5 A AC, 50/60 Hz.
- ACC Input: ±3 VDC.
- Output: 65 VDC at 12 ADC.
- Unit Type: Encapsulated – Rugged.
- Weight: 1.5 kg.
- Dimensions: 9.4 × 7.1 × 3.5 inches.
- Mounting: 4 mounting holes.
- Warranty: 1 year.
Original | Mecc Alte AVR SR7/2-G | Electronic Voltage Regulator | 391600126
AVR for Mecc Alte Brushless Generator Alternators 50/60 Hz- MECC ALTE: Direct replacement for the SR7 AVR on Mecc Alte brushless alternators.
- WIDE INPUT: Takes 80–270 Vac supply and 80–350 Vac single-phase sensing.
- 50 OR 60 HZ: Set with a jumper (bridge terminals 5A–6 for 60 Hz).
- BUILT-IN PROTECTION: Low-frequency protection lowers voltage when engine speed drops. Delayed overexcitation protection waits 15–20 s, so motors can still start.
- FIELD-ADJUSTABLE: VOLT, STAB, Hz and AMP trimmers, plus terminals for an optional 100 kΩ remote pot (±5%). Has a replaceable 5 A fuse and self-excites from residual voltage.
Original | Mecc Alte AVR UVR6/1-F | Electronic Voltage Regulator | 391600117
3-Phase Sensing, 50/60 Hz, for Mecc Alte Brushless Generator Alternators- Mecc Alte: names the UVR6 as the replacement for its discontinued RT80, RT80A, RT83 and RT83B regulators.
- 3-PHASE SENSING: Three sensing inputs let it regulate on one phase or on the average of all three.
- Works on star, delta and 12-lead machines.
- ±1% REGULATION: Holds voltage from no load to full load, at power factor 1 to 0.8, and when engine speed drops up to 6%.
- WIDE RANGE: For 80–480 Vac alternators. Runs at 50 Hz as standard and at 60 Hz with a jumper.
- PROTECTION + LED STATUS: Yellow LED for delayed overload protection, red for low speed, green for normal operation. Resin-filled against vibration and moisture, with a replaceable 6.3 A fuse.
AVR AS440 | Original
Features include:- Stability adjustment
- Optimum response selection
- Under frequency roll off adjustment
- Droop adjustment
- Trim adjustment
Call for Quotefor international purchases!
Read moreAVR MX321 | Original
Features include:- Stability selection & adjustment *Under frequency roll off adjustment
- Dip adjustment *Dwell adjustment
- Droop adjustment *Trim adjustment
- Over excitation adjustment *Over voltage adjustment
- Current limit adjustment *Ramp adjustment
Call for Quotefor international purchases!
Read moreAVR MX341 | Original
- Features include:
- Stability adjustment *Optimum response selection
- Under frequency roll off adjustment *Dip adjustment
- Droop adjustment *Trim adjustment
- Over excitation adjustment
Call for Quotefor international purchases!
Read moreLeroy Somer R230 | Original
R230 AVR option
- Potentiometer for remote voltage adjustment
- 1000 Ω / 0.5 W min: adjustment range ± 5%. – Remove the ST4 jumper.
Leroy Somer R250 | Original
- Power Input: AC 80-140V (50 / 60Hz)
- Maximum output: DC 90V / 6A / 10S
- Detection voltage input: AC 115V
- Voltage regulation rate: ≤ ± 1% External voltage trimming 1K / 2W potentiometer ± 10%
- Voltage regulation +/- 0.5% at steady state and constant speed
Leroy Somer AVR R438 | Original
Fuse: F1on X1,X2.10A;slow-250V- Voltage sensing : 5 VA isolated via trans- former • 0-110 V terminals = 95 to 140 V • 0-220 V terminals = 170 to 260 V • 0-380 V terminals = 340 to 520 V for other voltages, a transformer should be used.
- Voltage regulation ± 0.5%
- Normal or rapid response time via jumper ST2 (see below)
- Voltage adjustment via potentiometer P2 or apply a DC voltage of ± 1 V on the terminals of the external potentiometer
- Current sensing: (parallel operation): input S1, S2 intended for 1 C.T. Š 2.5 VA cl1, secondary 1A (optional)
- Quadrature droop adjustment via potentio- meter P1
Leroy Somer AVR R448 | Original
- Voltage regulation ± 0.5%
- Short circuit capability: 3 x Irated for 10 seconds (AREP or PMG excitation)
- Voltage sensing: 95 to 140 volts (50/60 Hz) or 170 to 260 volts (50/60 Hz) or 340 to 520 volts (50/60 Hz)
- Response time: Normal (1 sec) for ± 20% voltage variation or Rapid (0.3 sec) for ± 20% voltage variation
- Remote voltage adjustment range of: ± 5%
Leroy Somer AVR R449 | Original
- Automatic Voltage Regulator | Exact Generic Replacement for R449
- Steady state voltage regulation ± 0.5%
- Short circuit capability: 3 x Irated for 10 seconds (AREP or PMG excitation)
- Voltage sensing: 0-110v Terminals = 95 to 140 volts (50/60 Hz) or 0-220v Terminals = 170 to 260 volts (50/60 Hz) or 0-380v Terminals = 340 to 520 volts (50/60 Hz)
- Response time: Normal (1 sec) for ± 20% voltage variation or Rapid (0.3 sec) for ± 20% voltage variation. Remote voltage adjustment range: ± 5%
Leroy Somer AVR R450 | Original
The R450 AVR is supplied in a casing designed to be mounted on a panel with dampers.- Operating temperature: – 30°C to + 65° C. – Storage temperature: – 55°C to + 85°C.
- Shocks on the base: 9 g depending on the 3 axes.
- Vibrations: less than 10 Hz, 2 mm half-peak amplitude 10 Hz to 100 Hz: 100 mm/s, above 100 Hz: 8 g.
